Nine-metre cable selection
- Pair a 1.0 m probe with an 8.0 m extension cable.
- Pair the special 3.0 m 330101 probe with a 6.0 m extension cable.
- Rebuild a former 5.0 m chain rather than retaining it unchanged.
Item NO.:
330180-92-05Order(MOQ):
1Goods Stock:
12Payment:
T/TLead Time：
In stockWeight:
0.25KGDimension:
8.8x7x3cmDescription:
PROXIMITY SWITCHPrice:
AskA 3300 XL 8 mm Proximitor Sensor for a 9.0 m matched system, supplied without mounting hardware and configured for CSA/ATEX/IECEx approvals.
A 9.0 m matched measurement chain is the defining requirement for 330180-92-05, a 3300 XL 8 mm Proximitor Sensor that conditions the connected probe signal for the monitoring channel.
Panel planning for 330180-92-05 includes a suitable mounting base and fasteners because code 92 supplies the sensor without mounting hardware.
Two supported length combinations serve 330180-92-05: a 1.0 m probe with an 8.0 m extension cable, or the special 3.0 m 330101 probe with a 6.0 m cable; option 05 provides CSA, ATEX and IECEx approvals.
Option 92 is supplied without mounting hardware. The site therefore provides a suitable mounting base, fasteners, terminal access and the panel space needed for installation.
An 8.0 m 3300 XL extension cable completes the required 9.0 m electrical length. The probe, cable and sensor remain within the compatible 3300 XL 8 mm system.
That combination is supported for the 9.0 m system. The special 3.0 m option is available on the 330101 probe and pairs with a 6.0 m extension cable.
The published performance basis uses a 10 kΩ load, and the sensor output resistance is 50 Ω. A second parallel input changes the effective load, so the original test basis no longer applies; the total input impedance needs to be established before the shift is treated as a sensor or 9.0 m chain fault.
A barrier-fed installation operates from −23 to −26 Vdc, so −22 Vdc falls outside that range. The broader −17.5 to −26 Vdc range applies only when the sensor operates without barriers.
The published 9 m-sensor table shows measurable 60 Hz magnetic-field response, increasing from 0.0247 mil pp/Gauss at a 10 mil gap to 0.0348 at 90 mil. Comparing the disturbance with the nearby field and actual probe gap helps separate magnetic pickup from genuine shaft movement before any calibration change.
The supplied product is covered for 12 months under ApterPLC's sales terms. Keep the product nameplate, original packaging and transaction record available if warranty support is required.
|
9200-06-02-10-00 |
128031-01C |
330101-00-08-10-02-00 |
|
330854-080-25-00 |
991-06-70-01-00 |
330101-00-08-20-02-05 |
|
10026-02-12-05-02 |
VELOMITOR 330500 |
330101-00-12-10-02-05 |
|
10030-05-30-05-02 |
130944-01 128275-01F |
330101-00-15-10-02-00 |
|
330104-00-12-10-02-05 |
330103-11-19-10-02-00 |
330101-00-16-10-02-00 |
|
330104-00-12-10-02-00 |
330103-00-07-10-02-00 |
330101-00-18-10-02-05 |
|
330104-00-14-05-02-00 |
330103-00-07-20-02-00 |
330101-00-19-10-02-00 |
|
330104-00-16-05-02-00 |
330103-00-08-05-02-00 |
330101-00-28-05-02-00 |
|
330104-00-17-05-02-00 |
330104-00-15-05-02-00 |
330101-00-30-10-02-05 |
|
330104-00-18-10-02-05 |
330103-00-08-10-02-00 |
330101-00-40-10-02-00 |
|
330103-12-25-10-01-00 |
330103-00-08-10-02-05 |
330101-00-50-10-02-00 |
|
330104-12-20-10-01-00 |
330103-00-09-10-02-00 |
330101-00-56-10-02-00 |
|
330104-00-24-05-02-00 |
330104-00-08-05-02-00 |
330101-00-60-10-02-00 |
|
330104-00-24-10-02-00 |
330103-00-08-05-02-CN |
330101-00-63-10-02-00 |
|
330703-000-050-10-02-05 |
330851-04-000-020-10-01-00 |
330101-00-12-10-01-CN |
Related Tags :
SALES SUPPORT
32D floor,Guomao building,Hubin South Road,Siming District,Xiamen,Fujian,China.
Apter Power sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
Apter Power is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
