Selection
- Match the NSv system family, M10 x 1 reverse-mount geometry and 0.5 m probe lead.
- Verify the exact CN option and the complete probe-to-Proximitor system length.
Item NO.:
330907-05-30-05-02-CNOrder(MOQ):
1Goods Stock:
23Payment:
T/TLead Time：
In stockWeight:
0.08KGDimension:
21.5x23x3.5cmDescription:
Proximity SensorPrice:
AskM10 x 1 reverse-mount 3300 XL NSv probe with 5.08 mm unthreaded length, 30.48 mm case, 0.5 m lead and CN option.
330907-05-30-05-02-CN is a Bently Nevada 3300 XL NSv reverse-mount proximity probe with an M10 x 1 thread.
The ordering code identifies a 5.08 mm unthreaded length, 30.48 mm case, 0.5 m total probe length, standard-cable ClickLoc connector and CN country option.
Reverse-mount NSv probes do not offer armor or connector-protector options. Confirm the matched NSv Proximitor Sensor, system length, mounting geometry and installed gap before replacement.
The NSv system is intended for compressors and other fluid-film bearing machines where tight counterbore, side-view or rear-view clearances matter. Its published uses include radial vibration and position, axial position, tachometer or zero-speed measurement, and Keyphasor reference.
Its probe lead is 0.5 m. The official extension-cable choices make a 4.5 m cable appropriate for a documented 5 m sensor or a 6.5 m cable for a documented 7 m sensor; the probe and cable lengths must add up to the Proximitor Sensor length.
The flat target has an 8.9 mm minimum and a 13 mm recommended minimum diameter. The counterbore has a 9.5 mm minimum and a 13 mm recommended minimum; smaller geometry can change scale factor, especially at farther gaps.
The reverse-mount probe uses 7.5 N m recommended torque, allows no more than 15 mm of M10 x 1 thread engagement and requires a 25.4 mm minimum cable bend radius. Its ClickLoc joint is finger-tight, with 0.56 N m maximum connector torque.
The matched NSv Proximitor Sensor requires -17.5 to -26 Vdc at 12 mA maximum, or -23 to -26 Vdc with barriers. The monitor connection uses shielded three-conductor wiring, 0.2 to 1.5 mm2, with a 305 m maximum published run.
The published setting is 1.0 mm. Under the stated AISI 4140 steel target and system conditions, the 1.5 mm linear range extends approximately from 0.25 to 1.75 mm; another target material needs its own calibration basis.
Closely spaced probes on a small shaft can allow their emitted fields to interact and produce erroneous readings. The official minimum tip separation is 25 mm for axial measurements or 23 mm for radial measurements, with additional shaft-diameter conditions for standard and offset X-Y layouts.
The manufacturer requires the probe, extension cable and Proximitor Sensor to be replaced with NSv components for those upgrades. A partial family mix is not the documented migration path.
The supplied product is covered for 12 months under ApterPLC sales terms. Retain the complete product label, original packaging and transaction record so the exact unit can be identified quickly if warranty support is needed.
Includes an ApterPLC guide page and selected manufacturer pages covering NSv system specifications, the 330907 reverse-mount ordering table, probe drawings and CN country-option evidence.
|
3300/53 |
4454-156 |
1701/15 |
|
3300/21 |
16137-174 |
136294-01 |
|
990-04-XX-01-CN |
16137-177 |
330180-52-05 |
|
330354-040-24-05 |
330980-70-05 |
330104-00-06-10-02-00 |
|
330930-045-00-00 |
330180-92-05 |
330104-00-06-10-11-00 |
|
330130-070-00-CN |
177230-01-01-CN |
330104-00-07-05-02-00 |
|
3500/93 135799-02 |
330930-060-00-05 |
330103-11-19-10-02-00 |
|
3500/93 135785-02 |
3500/62 133811-03 |
330104-00-07-90-02-00 |
|
330103-05-15-05-02-00 |
3500/70M 140734-09 |
330104-00-08-05-02-00 |
|
330104-00-15-10-02-00 |
330905-08-13-10-02-05 |
330104-05-13-10-02-00 |
|
330106-05-30-50-02-00 |
330104-01-08-10-01-05 |
330104-05-15-05-02-00 |
|
330907-05-30-05-02-05 |
330101-00-20-05-02-05 |
330104-06-12-10-02-00 |
|
330106-05-30-20-02-CN |
330104-06-14-50-02-00 |
330104-10-18-10-01-00 |
|
330103-00-05-20-02-CN |
330103-00-04-10-12-00 |
330104-00-06-10-02-CN |
|
330851-02-000-030-10-00-05 |
330105-02-12-90-02-05 |
330104-00-07-10-02-CN |
Related Tags :
SALES SUPPORT
32D floor,Guomao building,Hubin South Road,Siming District,Xiamen,Fujian,China.
Apter Power sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
Apter Power is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
