Restricted-space selection
- Measure counterbore, side-view clearance and target size before choosing NSv.
- Keep NSv components together in a replacement chain.
- Do not substitute a standard 3300 XL 8 mm probe because the thread matches.
Item NO.:
330905-08-13-10-02-05Order(MOQ):
1Goods Stock:
16Payment:
T/TLead Time：
In stockWeight:
0.26KGDimension:
3.54x2.8x5.1cmDescription:
PROBEPrice:
AskAn unarmored M10 × 1 NSv probe with an 80 mm unthreaded section, 130 mm case, 1.0 m total length, unprotected ClickLoc connection and Multiple Approvals option.
Restricted counterbores, limited side or rear clearance and smaller targets are the intended setting for 330905-08-13-10-02-05, a compact M10 × 1 probe in the 3300 XL NSv family.
At the connection end, 330905-08-13-10-02-05 uses an option-02 ClickLoc joint without a protector and carries the option-05 Multiple Approvals configuration.
The 1.0 m length of 330905-08-13-10-02-05 pairs with a 4.0 m NSv extension cable for a 5.0 m chain or a 6.0 m NSv extension cable for a 7.0 m chain.
Case length alone does not establish the fit. The 80 mm unthreaded section, actual counterbore and side-view geometry, target position and available withdrawal path all form part of the machine-side installation envelope.
A 9 mm target is above the 8.9 mm minimum but below the 13 mm recommended minimum. It therefore falls into a below-recommended target condition, where usable response and gap need to suit the NSv target-size guidance.
This probe belongs in an NSv measurement chain. An NSv Proximitor Sensor accepts NSv or supported 3300 RAM probe-and-cable combinations, rather than a mixed standard 3300 XL 8 mm chain.
A 4.0 m NSv extension cable produces the 5.0 m system, while a 6.0 m NSv cable produces the 7.0 m system. The resulting probe-plus-cable length matches the selected NSv Proximitor Sensor.
Option 02 leaves the ClickLoc joint without a protector. A compatible connector protector is the suitable provision at exposed probe-to-extension and extension-to-sensor joints; silicone tape is not suited to turbine-oil exposure.
A standard X-Y arrangement uses a 30 mm minimum shaft diameter, or 20 mm when the probes are offset axially by 23 mm. Tip separation is at least 23 mm for radial measurements or 25 mm for axial measurements.
The supplied product is covered for 12 months under ApterPLC's sales terms. Keep the product nameplate, original packaging and transaction record available if warranty support is required.
|
9200-06-02-10-00 |
128031-01C |
330101-00-08-10-02-00 |
|
330854-080-25-00 |
991-06-70-01-00 |
330101-00-08-20-02-05 |
|
10026-02-12-05-02 |
VELOMITOR 330500 |
330101-00-12-10-02-05 |
|
10030-05-30-05-02 |
130944-01 128275-01F |
330101-00-15-10-02-00 |
|
330104-00-12-10-02-05 |
330103-11-19-10-02-00 |
330101-00-16-10-02-00 |
|
330104-00-12-10-02-00 |
330103-00-07-10-02-00 |
330101-00-18-10-02-05 |
|
330104-00-14-05-02-00 |
330103-00-07-20-02-00 |
330101-00-19-10-02-00 |
|
330104-00-16-05-02-00 |
330103-00-08-05-02-00 |
330101-00-28-05-02-00 |
|
330104-00-17-05-02-00 |
330104-00-15-05-02-00 |
330101-00-30-10-02-05 |
|
330104-00-18-10-02-05 |
330103-00-08-10-02-00 |
330101-00-40-10-02-00 |
|
330103-12-25-10-01-00 |
330103-00-08-10-02-05 |
330101-00-50-10-02-00 |
|
330104-12-20-10-01-00 |
330103-00-09-10-02-00 |
330101-00-56-10-02-00 |
|
330104-00-24-05-02-00 |
330104-00-08-05-02-00 |
330101-00-60-10-02-00 |
|
330104-00-24-10-02-00 |
330103-00-08-05-02-CN |
330101-00-63-10-02-00 |
|
330703-000-050-10-02-05 |
330851-04-000-020-10-01-00 |
330101-00-12-10-01-CN |
Related Tags :
SALES SUPPORT
32D floor,Guomao building,Hubin South Road,Siming District,Xiamen,Fujian,China.
Apter Power sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
Apter Power is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
