Selection
- Measure the required case reach and compare the complete suffix with the removed probe.
- Confirm that code 02 is acceptable for the exposed connector environment.
Item NO.:
330104-00-18-10-02-00Order(MOQ):
1Goods Stock:
16Payment:
T/TLead Time：
In stockWeight:
0.25KGDimension:
7.8x3x6.2cmDescription:
PROXIMITY PROBESPrice:
AskAn armored M10 × 1 probe with a 180 mm case and 1.0 m standard lead for deep-reach rotating-shaft monitoring points.
Deep bearing housings and remote brackets often need more mechanical reach than a standard probe body can provide. With its 180 mm M10 × 1 case, 330104-00-18-10-02-00 is configured for those longer insertion paths in a matched 3300 XL 8 mm system.
The armored lead helps 330104-00-18-10-02-00 tolerate demanding cable routes where abrasion or incidental contact is a concern. Because the probe body is long, good armor support also prevents cable weight from disturbing the final tip position.
Connector code 02 leaves the miniature ClickLoc joint without a separate protector. For installations exposed to oil or moisture, 330104-00-18-10-02-00 works best when the site already provides suitable connector protection and accessible routing for inspection.
It is intended for a deep M10 × 1 mounting point where the probe must reach through a long housing or bracket. Verify the available insertion path and adjustment range because a long case can fit the thread but still miss the correct target position.
Clamp or guide the armor so its mass and machine vibration cannot side-load the 180 mm probe body. Maintain the 25.4 mm minimum bend radius and keep the route away from hot, sharp or moving surfaces.
No. Connector code 02 is the standard miniature ClickLoc cable without a protector. Apply the site-approved environmental protection method while keeping the joint accessible for inspection.
Save the insertion depth, locknut position, final gap voltage, target state, cable route, connected extension cable and Proximitor model, plus the dynamic reading at a known machine condition.
Inspect armor support, tight bend points, ClickLoc seating, probe locknut security and sensor supply. Watch the bias while checking accessible connections so a route-induced fault is separated from an electronics fault.
Confirm zero unthreaded length, 180 mm case, 1.0 m lead, code 02 connector and code 00 approval. Adjacent 330104 case lengths are not mechanically interchangeable merely because the thread matches.
Supplied products are covered for 12 months under ApterPLC sales terms. Keep the complete nameplate, original packaging and transaction record so the exact unit and revision can be identified during support.
Support: sales1@apterpower.com · +8618020776782
Use this document to confirm the 3300 XL 8 mm armored metric probe ordering code, 180 mm case, 1 m lead, matching requirements, specifications and installation drawings.
Download the 330104-00-18-10-02-00 filtered official datasheet|
330104-06-12-10-02-00 |
330130-035-00-00 |
330130-040-02-00 |
|
330104-06-14-50-02-00 |
330130-035-00-CN |
330130-045-00-00 |
|
330104-10-18-10-01-00 |
330130-030-01-CN |
330130-045-00-05 |
|
330104-10-20-05-02-00 |
330106-00-04-10-02-00 |
330130-040-00-00 |
|
330104-10-20-10-02-05 |
330106-05-30-05-02-00 |
330130-040-00-05 |
|
330104-12-20-10-01-00 |
330105-02-12-50-02-00 |
330130-040-01-05 |
|
330104-13-20-10-02-00 |
330106-05-30-10-02-00 |
330130-045-01-00 |
|
330104-15-23-10-02-00 |
330106-05-30-10-02-05 |
330130-045-02-05 |
|
330104-19-25-10-11-05 |
330106-05-30-15-02-00 |
330130-045-03-05 |
|
330105-02-12-05-02-00 |
330106-05-30-50-02-00 |
330130-035-01-CN |
|
330105-02-12-05-02-05 |
330130-00-05-05-02-00 |
330130-045-00-CN |
|
330105-02-12-10-02-00 |
330106-05-30-05-02-CN |
330130-045-01-CN |
|
330105-02-12-15-12-05 |
330106-05-30-10-02-CN |
330130-040-00-CN |
|
330105-02-12-15-12-CN |
330106-05-30-15-02-CN |
330130-040-02-CN |
|
330105-02-12-05-02-CN |
330106-05-30-20-02-CN |
330130-040-10-CN |
Related Tags :
SALES SUPPORT
32D floor,Guomao building,Hubin South Road,Siming District,Xiamen,Fujian,China.
Apter Power sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks.
Apter Power is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
